LTE FDD
For Waveform Playback (ARB) capability.
This topic describes the settings of the Physical Channel node when the carrier is Basic Downlink.
Resource Block Collection Numbers
Resource Block Collection Numbers
PDCCH Transmission Configuration
Resource Block Collection Numbers
Resource Block Collection Numbers
PHICH Transmission Configuration
Resource Block Collection Numbers
The Number of Physical Channels depends on the user, but initially <channel> ranges are as follows:
PBCH: 1
PDCCH: 1
PCFICH: 1
PHICH: 1
PDSCH: 1-10
Displays the Physical Channel Number.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:NUMBer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:NUMBer? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Displays the Name.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:NAME? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:NAME? |
|
Dependencies |
|
|
Preset |
PBCH |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the state of PBCH channel.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:STATe? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:STATe? |
|
Notes |
This setting is read-only for physical channels that are controlled by a channel defined in the Transport Channel layer. |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets a value, in dB for the Power.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:POWer <real> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:POWer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:POWer 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:POWer? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-60 |
|
Max |
20 |
|
Initial S/W Revision |
A.20.01 |
Displays the Resource Block Collection Numbers.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:RBCollection:NUMBers? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:RBCollection:NUMBers? |
|
Dependencies |
|
|
Preset |
- |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Data.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:DATA? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:DATA? |
|
Dependencies |
|
|
Preset |
Higher Layer |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the name of the transport channel mapped to this physical channel when Data is set to Higher Layer.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:HLAYer:CHANnel? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:HLAYer:CHANnel? |
|
Dependencies |
Visible only when Data is set to Higher Layer |
|
Preset |
N/A |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Turns Scrambling on or off.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:SCRambling ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCH<channel>:SCRambling? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:SCRambling ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PBCH:SCRambling? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Physical Channel Number.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:NUMBer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:NUMBer? |
|
Dependencies |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Displays the Name.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:NAME? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:NAME? |
|
Dependencies |
|
|
Preset |
PDCCH |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the state of the PDCCH Channel.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:STATe? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:STATe? |
|
Notes |
This setting is read-only for physical channels that are controlled by a channel defined in the Transport Channel layer. |
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets a value, in dB for the Power.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:POWer <real> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:POWer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:POWer 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:POWer? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-60 |
|
Max |
20 |
|
Initial S/W Revision |
A.20.01 |
Displays the Resource Block Collection Numbers.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:RBCollection:NUMBers? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:RBCollection:NUMBers? |
|
Dependencies |
|
|
Preset |
- |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Turns Scrambling on or off.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:SCRambling ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:SCRambling? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:SCRambling ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:SCRambling? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the PDCCH Allocations.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:ALLocations? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:ALLocations? |
|
Dependencies |
The values you set here are displayed in the CFI cell for the corresponding PCFICH channel. |
|
Preset |
1 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
The Number Of Transmissions <tx> initially for PDCCH is 0-9. You can change the number of Transmission as per your requirements.
Displays the PDCCH #.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>:NUMBer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:NUMBer? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
99 |
|
Initial S/W Revision |
A.20.01 |
Sets or displays the Data.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>:DATA PN9|PN15 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>:DATA? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:DATA PN9 RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:DATA? |
|
Couplings |
|
|
Preset |
PN9 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets or displays the Data.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>:DATA:USER "StringBits" [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PBCCH<channel>:TX<tx>:DATA:USER? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:DATA:USER "00000000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:DATA:USER? |
|
Couplings |
|
|
Preset |
00000000 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Selects the CCE Aggregation Level.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>:CCE:AGGRegation L1|L2|L4|L8 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>:CCE:AGGRegation? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:CCE:AGGRegation L1 RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:CCE:AGGRegation? |
|
Dependencies |
|
|
Preset |
L1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets the CCE offset index for this PDCCH allocation.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>:CCE:OFFSet <integer> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>:CCE:OFFSet? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:CCE:OFFSet 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX:CCE:OFFSet? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
39 |
|
Initial S/W Revision |
A.20.01 |
Turns State on or off.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDCCh<channel>:TX<tx>[:STATe]? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDCCh:TX? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Physical Channel Number.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFich<channel>:NUMBer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk: PCFich:NUMBer? |
|
Dependencies |
|
|
Preset |
13 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Displays the Name.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFich<channel>:NAME? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk: PCFich:NAME? |
|
Dependencies |
|
|
Preset |
PCFICH |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the state of PCFICH Channel.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFich<channel>:STATe? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PCFich:STATe? |
|
Dependencies |
This setting is read-only for physical channels that are controlled by a channel defined in the Transport Channel layer. |
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets a value, in dB for the Power.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFIch<channel>:POWer <real> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFIch<channel>:POWer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PCFich:POWer 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:PCFich:POWer? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-60 |
|
Max |
20 |
|
Initial S/W Revision |
A.20.01 |
Displays the Resource Block Collection Numbers.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFich<channel>:RBCollection:NUMBers? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PCFich:RBCollection:NUMBers? |
|
Dependencies |
|
|
Preset |
- |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Turns scrambling for the physical channel on or off.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFich<channel>:SCRambling ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFich<channel>:SCRambling? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PCFich:SCRambling ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PCFich:SCRambling? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Modulation Type.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFich<channel>:MODulation:TYPE? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PCFich:MODulation:TYPE? |
|
Dependencies |
|
|
Preset |
QPSK |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the CFI.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PCFich<channel>:CFI? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PCFich:CFI? |
|
Dependencies |
Displays the control format indicator for each subframe in the selected PCFICH channel, separated by commas. These values correspond to the number of OFDM symbols used for transmission of the PDCCH in each subframe and are set in the PDCCH Allocations cell. |
|
Preset |
1,1,1,1,1,1,1,1,1,1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Physical Channel Number.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:NUMBer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:NUMBer? |
|
Dependencies |
|
|
Preset |
14 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Displays the Name.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:NAME? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:NAME? |
|
Dependencies |
|
|
Preset |
PHICH |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Turns the State ON or OFF.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:STATe ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:STATe? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:STATe? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Resource Block Collection Numbers.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:RBCollection:NUMBers? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:RBCollection:NUMBers? |
|
Dependencies |
|
|
Preset |
- |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Turns Scrambling on or off.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:SCRambling ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:SCRambling? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:SCRambling ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:SCRambling? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the PHICH BPSK Symbol Power.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:BPSK:POWer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:BPSK:POWer? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-60 |
|
Max |
20 |
|
Initial S/W Revision |
A.20.01 |
Displays the PHICH Duration.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:PHICH:DURation NORMal|EXTended [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:PHICH:DURation? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:DURation NORM RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:DURation? |
|
Dependencies |
|
|
Preset |
NORM |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the PHICH Maximum Group Number.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:MAXGroup? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:MAXGroup? |
|
Dependencies |
|
|
Preset |
2 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Displays the PHICH Allocation.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:ALLocation ONESIXTH|ONEHALF|ONE|TWO [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:ALLocation? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:ALLocation ONESIXTH RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:ALLocation? |
|
Dependencies |
|
|
Preset |
ONESIXTH |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
The Number Of Transmissions <tx> initially defined for PHICH is 0-15. You can change the number of Transmission as per your requirements.
The <tx> value can be calculated using the following formula:
<tx> value = Group # value * 8 + Sequence Index value
Initially, only PHICH Sequence Index 0 of Group 0 and Group 1 is enabled.
Displays the Group #.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:TX<tx>:GROup:NUMBer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:TX:GROup:NUMBer? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
99 |
|
Initial S/W Revision |
A.20.01 |
Displays the Sequence Index.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:TX<tx>:SEQuence:INDex? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:TX:SEQuence:INDex? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
0 |
|
Max |
7 |
|
Initial S/W Revision |
A.20.01 |
Sets the HARQ Indicator (HI) value for this PHICH transmission configuration.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:TX<tx>:HI ACK|NACK [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:TX<tx>:HI? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:TX:HI ACK RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:TX:HI? |
|
Dependencies |
This setting is available only if the State for particular Sequence Index in a Grp is enabled. |
|
Preset |
ACK |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Data source for the PHICH Tx Config
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk: PHICh<channel>:TX<tx>:HI:USER "stringbits" [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk: PHICh<channel>:TX<tx>:HI:USER? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:TX:HI:USER "0000" RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:TX:HI:USER? |
|
Dependencies |
|
|
Preset |
"" |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Turns the State ON or OFF.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:TX<tx>[:STATe] ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PHICh<channel>:TX<tx>[:STATe]? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:TX ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PHICh:TX? |
|
Notes |
The Preset value is not applicable for this setting since for all Tx this is not 1. It depends on the user to turn these ON or OFF. By default, only Seq Index 0 of Grp 0 and Grp 1 is enabled with PHICH Max Group Number 2. |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Physical Channel Number.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:NUMBer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:NUMBer? |
|
Dependencies |
The preset value depends on the PDSCH number. It is dynamically allotted PDSCH. |
|
Preset |
3 |
|
State Saved |
Yes |
|
Min |
N/A |
|
Max |
N/A |
|
Initial S/W Revision |
A.20.01 |
Displays the Name.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:NAME? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:NAME? |
|
Dependencies |
|
|
Preset |
PDSCH |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Turns the State on or off.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:STATe ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:STATe? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:STATe ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:STATe? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Sets a value, in dB for the Power.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:POWer <real> [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:POWer? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:POWer 0 RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:POWer? |
|
Dependencies |
|
|
Preset |
0 |
|
State Saved |
Yes |
|
Min |
-60 |
|
Max |
20 |
|
Initial S/W Revision |
A.20.01 |
Displays the Resource Block Collection Numbers.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:RBCollection:NUMBers? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:RBCollection:NUMBers? |
|
Dependencies |
|
|
Preset |
1,2 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the Data.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:DATA? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:DATA? |
|
Dependencies |
Higher Layer is displayed in the Data cell if the selected physical channel is controlled by a channel defined in the Transport Channel layer. |
|
Preset |
Higher Layer |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Displays the name of the transport channel mapped to this physical channel when Data is set to Higher Layer.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:HLAYer:CHANnel? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:HLAYer:CHANnel? |
|
Dependencies |
Visible only when Data is set to Higher Layer |
|
Preset |
CH1: DL-SCH |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |
Turns Scrambling on or off.
|
SCPI Command |
[:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:SCRambling ON|OFF|1|0 [:SOURce]:RADio:LTEFdd:WAVeform[:ARB]:CCARrier<channel>:DLINk:PDSCh<channel>:SCRambling? |
|
SCPI Example |
RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:SCRambling ON RADio:LTEFdd:WAVeform:CCARrier:DLINk:PDSCh:SCRambling? |
|
Dependencies |
|
|
Preset |
1 |
|
State Saved |
Yes |
|
Initial S/W Revision |
A.20.01 |